AD-APARD32690-SL

Overview

The AD-APARD32690-SL is a platform for prototyping intelligent, secure, and connected field devices. It has an Arduino Mega-compatible form factor and two Pmod-compatible connectors. The system includes the MAX32690 ARM Cortex-M4 with FPU-Based Microcontroller and Bluetooth LE 5.2. The MCU is coupled with external RAM (2 x 512 Mb) and Flash (64 Mb) memories to meet the requirements of the most demanding applications. The MAXQ1065 security coprocessor enables state of the art security features such as for root-of-trust, mutual authentication, data confidentiality and integrity, secure boot, and secure communications. A 10 Mbps single-pair Ethernet link using the ADIN1110 10BASE-T1L MAC/PHY, enables remote data acquisition and system configuration. The 10BASE-T1L interface also supports Single-pair Power over Ethernet (SPoE) and be used for powering the system via an Arduino shield implementing the required power circuitry.

The Zephyr port is running on the MAX32690 MCU.

Hardware

  • MAX32690 MCU:

    • Ultra-Efficient Microcontroller for Battery-Powered Applications

      • 120MHz Arm Cortex-M4 Processor with FPU

      • 7.3728MHz and 60MHz Low-Power Oscillators

      • External Crystal Support (32MHz required for BLE)

      • 32.768kHz RTC Clock (Requires External Crystal)

      • 8kHz Always-On Ultra-Low Power Oscillator

      • 3MB Internal Flash, 1MB Internal SRAM (832kB ECC ON)

      • TBDμW/MHz Executing from Cache at 1.1V

      • 1.8V and 3.3V I/O with No Level Translators

      • External Flash & SRAM Expansion Interfaces

    • Bluetooth 5.2 LE Radio

      • Dedicated, Ultra-Low-Power, 32-Bit RISC-V Coprocessor to Offload Timing-Critical Bluetooth Processing

      • Fully Open-Source Bluetooth 5.2 Stack Available

      • Supports AoA, AoD, LE Audio, and Mesh

      • High-Throughput (2Mbps) Mode

      • Long-Range (125kbps and 500kbps) Modes

      • Rx Sensitivity: -97.5dBm; Tx Power: +4.5dBm

      • Single-Ended Antenna Connection (50Ω)

    • Multiple Peripherals for System Control

      • 16-Channel DMA

      • Up To Five Quad SPI Master (60MHz)/Slave (48MHz)

      • Up To Four 1Mbaud UARTs with Flow Control

      • Up To Two 1MHz I2C Master/Slave

      • I2S Master/Slave

      • Eight External Channel, 12-bit 1MSPS SAR ADC w/ on-die temperature sensor

      • USB 2.0 Hi-Speed Device

      • 16 Pulse Train Engines

      • Up To Six 32-Bit Timers with 8mA High Drive

      • Up To Two CAN 2.0 Controllers

      • Up To Four Micro-Power Comparators

      • 1-Wire Master

    • Security and Integrity

      • ChipDNA Physically Un-clonable Function (PUF)

      • Modular Arithmetic Accelerator (MAA), True Random Number Generator (TRNG)

      • Secure Nonvolatile Key Storage, SHA-256, AES-128/192/256

      • Secure Boot ROM

  • External devices connected to the APARD32690:

    • On-Board HyperRAM

    • On-Board SPI Flash

    • USB 2.0 Type-C interface to the MAX32690

    • SPI PMOD connector

    • I2C PMOD connector

    • SWD 10-Pin Header

    • On-Board Bluetooth 5.2 LE Radio antenna

    • MAXQ1065 Ultralow Power Cryptographic Controller with ChipDNA

    • ADIN1110 Robust, Industrial, Low Power 10BASE-T1L Ethernet MAC-PHY

    • U-Blox NINA-W102 802.11b/g/n module with dual-mode Bluetooth v4.2

    • On-Board 5V, 3.3V, 1.8V, and 1.1V voltage regulators

    • 2-Pin external power supply terminal block (5V - 28V DC)

    • Board Power Provided by either the USB Port or the 2-Pin connector

    • Arduino Mega compatible header.

    • Two general-purpose LEDs and one general purpose push button.

Supported Features

Below interfaces are supported by Zephyr on APARD32690.

Interface

Controller

Driver/Component

NVIC

on-chip

nested vector interrupt controller

SYSTICK

on-chip

systick

CLOCK

on-chip

clock and reset control

GPIO

on-chip

gpio

UART

on-chip

serial

SPI

on-chip

spi

ADIN1110

spi

ADIN1110 10BASE-T1L mac/phy

TRNG

on-chip

entropy

Timer

on-chip

counter

W1

on-chip

one wire master

Connections and IOs

Name

Name

Settings

Description

P55

SWD TX

1-2

2-3

Connects the SWD UART TX to the (UART) RX port of the U-Blox Nina W102.

Connects the SWD UART TX to the UART0 TX pin of the MAX32690.

P50

SWD RX

1-2

2-3

Connects the SWD UART RX to the (UART) TX port of the U-Blox Nina W102.

Connects the SWD UART RX to the UART0 RX pin of the MAX32690.

P51

SWD POW

1-2

2-3

Connects the SWD Vcc pin to 3.3V.

Connects the SWD Vcc pin to 1.8V.

P38

UART RX WIFI

1-2

Open

Connect the U-Blox Nina W102 UART RX to the UART2A TX pin of the MAX32690

Disconnects the U-Blox Nina W102 UART RX from the UART2A TX pin

P58

UART TX WIFI

1-2

Open

Connect the U-Blox Nina W102 UART TX to the UART2A RX pin of the MAX32690.

Disconnects the U-Blox Nina W102 UART TX from the UART2A RX pin.

S4

SW1

On

Off

Pulls the ADIN1110’s SWPD_EN pin to 3.3V through a resistor.

Leaves the ADIN1110’s SWPD_EN pin floating.

S4

SW2

On

Off

Pulls the ADIN1110’s CFG0 pin to 3.3V through a resistor.

Leaves the ADIN1110’s CFG0 pin floating.

S4

SW3

On

Off

Pulls the ADIN1110’s CFG1 pin to 3.3V through a resistor.

Leaves the ADIN1110’s CFG1 pin floating.

Programming and Debugging

Flashing

The MAX32690 MCU can be flashed by connecting an external debug probe to the SWD port. SWD debug can be accessed through the Cortex 10-pin connector, P9. Logic levels are either 1.8V or 3.3V (based on P51 selection).

Once the debug probe is connected to your host computer, then you can simply run the west flash command to write a firmware image into flash.

Note

This board uses OpenOCD as the default debug interface. You can also use a Segger J-Link with Segger’s native tooling by overriding the runner, appending --runner jlink to your west command(s). The J-Link should be connected to the standard 2*5 pin debug connector (P9) using an appropriate adapter board and cable.

Debugging

Please refer to the Flashing section and run the west debug command instead of west flash.

References