st,lsm303agr-accel (on i2c bus)

Description

STMicroelectronics LSM303AGR 3-axis accelerometer accessed through I2C bus

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`supply-gpios`	`phandle-array`	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
`vin-supply`	`phandle`	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.
`irq-gpios`	`phandle-array`	The INT1 and (optional) INT2 signal connections. These signals are active-high as produced by the sensor.
`int1-gpio-config`	`int`	Select the interrupt configuration for INT1 gpio. The default of 0 is the most common situation to avoid multiple interrupts to be triggered by same event. - 0 # LIS2DH_DT_GPIO_INT_EDGE_BOTH - 1 # LIS2DH_DT_GPIO_INT_EDGE_RISING - 2 # LIS2DH_DT_GPIO_INT_EDGE_FALLING - 3 # LIS2DH_DT_GPIO_INT_LEVEL_HIGH - 4 # LIS2DH_DT_GPIO_INT_LEVEL_LOW Legal values: `0`, `1`, `2`, `3`, `4`
`int2-gpio-config`	`int`	Select the interrupt configuration for INT2 gpio. The default of 0 is the most common situation to avoid multiple interrupts to be triggered by same event. - 0 # LIS2DH_DT_GPIO_INT_EDGE_BOTH - 1 # LIS2DH_DT_GPIO_INT_EDGE_RISING - 2 # LIS2DH_DT_GPIO_INT_EDGE_FALLING - 3 # LIS2DH_DT_GPIO_INT_LEVEL_HIGH - 4 # LIS2DH_DT_GPIO_INT_LEVEL_LOW Legal values: `0`, `1`, `2`, `3`, `4`
`disconnect-sdo-sa0-pull-up`	`boolean`	Indicates the device driver should disconnect SDO/SA0 pull-up during device initialization (e.g. to save current leakage). Note that only subset of devices supported by this binding have SDO/SA0 pull-up (e.g. LIS2DH12, LIS3DH).
`anym-on-int1`	`boolean`	Indicates that the device driver should use interrupt 1 for any movement. This is for boards that only have one interrupt line connected from the sensor to the processor.
`anym-no-latch`	`boolean`	Disable the latching of interrupts for any movement.
`anym-mode`	`int`	Select the interrupt mode for any movement. The default of 0 is the power-on-reset value. - 0 # LIS2DH_DT_ANYM_OR_COMBINATION - 1 # LIS2DH_DT_ANYM_6D_MOVEMENT - 2 # LIS2DH_DT_ANYM_AND_COMBINATION - 3 # LIS2DH_DT_ANYM_6D_POSITION Legal values: `0`, `1`, `2`, `3`
`friendly-name`	`string`	Human readable string describing the sensor. It can be used to distinguish multiple instances of the same model (e.g., lid accelerometer vs. base accelerometer in a laptop) to a host operating system. This property is defined in the Generic Sensor Property Usages of the HID Usage Tables specification (https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “st,lsm303agr-accel” compatible.

Name	Type	Details
`reg`	`array`	device address on i2c bus This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.