nxp,imx93-pinctrl

Description

The node has the 'pinctrl' node label set in MCUX SoC's devicetree. These
nodes can be autogenerated using the MCUXpresso config tools combined with
the imx_dts_gen.py script in NXP's HAL. The mux, mode, input, daisy, and cfg
fields in a group select the pins to be configured, and the remaining
devicetree properties set configuration values for those pins
for example, here is an group configuring LPUART1 pins:

group0 {
  pinmux = <&iomuxc_uart2_rxd_uart_rx_uart2_rx,
    &iomuxc_uart2_txd_uart_tx_uart2_tx>;
    bias-pull-up;
    slew-rate = "slow";
    drive-strength = "x1";
};

This will select UART2_RXD as UART2 rx, and UART2_TXD as UART2 tx.
Both pins will be configured with a slow slew rate, and x1 drive
strength.
Note that the soc level iomuxc dts file can be examined to find the possible
pinmux options. Here are the affects of each property on the
IOMUXC SW_PAD_CTL register:
input-schmitt-enable: HYS=1
drive-open-drain: OD=1
bias-pull-down: PD=0
bias-pull-up: PU
slew-rate: FSEL1=<enum_idx>
drive-strength: DSE=<enum_idx>
input-enable: SION=1 (in SW_MUX_CTL_PAD register)

If only required properties are supplied, the pin will have the following
configuration:
HYS=0,
PD=0
PU=0
OD=0,
FSEL1=<slew-rate>,
DSE=<drive-strength>,
SION=0,

Properties

Top level properties

These property descriptions apply to “nxp,imx93-pinctrl” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

(None)

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “nxp,imx93-pinctrl” compatible.

Name	Type	Details
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg`	`array`	register space See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.

Grandchild node properties

Name	Type	Details
`pinmux`	`phandles`	Pin mux selections for this group. See the soc level iomuxc DTSI file for a defined list of these options. This property is required.
`drive-strength`	`string`	Pin output drive strength. Sets the DSE field in the IOMUXC peripheral. 00_0000 X0, No driver 00_0001 X1 00_0011 X2 00_0111 X3 00_1111 X4 01_1111 X5 11_1111 X6 This property is required. Legal values: `'x0'`, `'x1'`, `'x2'`, `'x3'`, `'x4'`, `'x5'`, `'x6'`
`slew-rate`	`string`	Select slew rate for pin. Corresponds to SRE field in IOMUXC peripheral 0 SLOW — Slow Frequency Slew Rate 1 Slightly SLOW — Slightly Slow Frequency Slew Rate 2 Slightly FAST — Slightly Fast Frequency Slew Rate 3 FAST — Fast Frequency Slew Rate This property is required. Legal values: `'slow'`, `'slightly_slow'`, `'slightly_fast'`, `'fast'`
`bias-pull-up`	`boolean`	enable pull-up resistor
`bias-pull-down`	`boolean`	enable pull-down resistor
`drive-open-drain`	`boolean`	drive with open drain (hardware AND)
`input-enable`	`boolean`	enable input on pin (e.g. enable an input buffer, no effect on output)
`input-schmitt-enable`	`boolean`	enable schmitt-trigger mode