nordic,qspi-nor (on qspi bus)

Vendor: Nordic Semiconductor

Note

An implementation of a driver matching this compatible is available in drivers/flash/nrf_qspi_nor.c.

Description

QSPI NOR flash supporting the JEDEC CFI interface.

Properties

Node specific propertiesDeprecated node specific propertiesBase properties

Properties not inherited from the base binding file.

Name	Type	Details
jedec-id	uint8-array	JEDEC ID as manufacturer ID, memory type, memory density This property is required.
size	int	The size in bits. Set this or size-in-bytes, but not both.
size-in-bytes	int	The size in bytes. Set this or size, but not both.
quad-enable-requirements	string	Quad Enable Requirements value from JESD216 BFP DW15. Use NONE if the device detects 1-1-4 and 1-4-4 modes by the instruction. Use S1B6 if QE is bit 6 of the first status register byte, and can be configured by reading then writing one byte with RDSR and WRSR. For other fields see the specification. Default value: S1B6 Legal values: 'NONE', 'S2B1v1', 'S1B6', 'S2B7', 'S2B1v4', 'S2B1v5', 'S2B1v6'
readoc	string	Specify the number of data lines and opcode used for reading. If not provided fastread will be selected. Legal values: 'fastread', 'read2o', 'read2io', 'read4o', 'read4io'
writeoc	string	Specify the number of data lines and opcode used for writing. If not provided pp will be selected. Legal values: 'pp', 'pp2o', 'pp4o', 'pp4io'
address-size-32	boolean	Set to indicate that 32-bit addressing is to be used. If not specified 24-bit addressing will be used.
ppsize-512	boolean	Set to indicate that the write opcode operates on 512-byte pages. If not specified the write opcode operates on 256-byte pages.
sck-delay	int	Number of clock cycles CSn must be asserted before it can go low again, specified in nanoseconds.
rx-delay	int	Number of clock cycles from the rising edge of the SPI clock until the input serial data is sampled.
cpha	boolean	Set to indicate phase starts with asserted half-phase (CPHA=1). For this driver using this property requires also using cpol.
cpol	boolean	Set to indicate clock leading edge is falling (CPOL=1). For this driver using this property requires also using cpha.
sck-frequency	int	Maximum clock speed supported by the device, in Hz. This property is required.
requires-ulbpr	boolean	Indicates the device requires the ULBPR (0x98) command. Some flash chips such as the Microchip SST26VF series have a block protection register that initializes to write-protected. Use this property to indicate that the BPR must be unlocked before write operations can proceed.
has-dpd	boolean	Indicates the device supports the DPD (0xB9) command. Use this property to indicate the flash chip supports the Deep Power-Down mode that is entered by command 0xB9 to reduce power consumption below normal standby levels. Use of this property implies that the RDPD (0xAB) Release from Deep Power Down command is also supported. (On some chips this command functions as Read Electronic Signature; see t-enter-dpd).
dpd-wakeup-sequence	array	Specifies wakeup durations for devices without RDPD. Some devices (Macronix MX25R in particular) wake from deep power down by a timed sequence of CSn toggles rather than the RDPD command. This property specifies three durations measured in nanoseconds, in this order: (1) tDPDD (Delay Time for Release from Deep Power-Down Mode) (2) tCDRP (CSn Toggling Time before Release from Deep Power-Down Mode) (3) tRDP (Recovery Time for Release from Deep Power-Down Mode) Absence of this property indicates that the RDPD command should be used to wake the chip from Deep Power-Down mode.
t-enter-dpd	int	Duration required to complete the DPD command. This provides the duration, in nanoseconds, that CSn must be remain deasserted after issuing DPD before the chip will enter deep power down. If not provided the driver does not enforce a delay.
t-exit-dpd	int	Duration required to complete the RDPD command. This provides the duration, in nanoseconds, that CSn must be remain deasserted after issuing RDPD before the chip will exit deep power down and be ready to receive additional commands. If not provided the driver does not enforce a delay.
has-lock	int	Bit mask of bits of the status register that should be cleared on startup. Some devices from certain vendors power-up with block protect bits set in the status register, which prevent any erase or program operation from working. Devices that have this behavior need to clear those bits on startup. However, other devices have non-volatile bits in the status register that should not be cleared. This value, when present, identifies bits in the status register that should be cleared when the device is initialized.
mxicy,mx25r-power-mode	string	Select to configure flash to use ultra low power mode or high performance mode (L/H switch). The high performance mode has faster write and erase performance, but use more power than ultra low power mode. Only supported on Macronix MX25R Ultra Low Power series. Legal values: 'low-power', 'high-performance'
use-4b-addr-opcodes	boolean	Indicates the device uses special 4-byte address opcodes. Instead of switching to 4-byte addressing mode, the device uses special opcodes for 4-byte addressing. Some devices support 4-byte address opcodes for read/write/erase operations. Use this property to indicate that the device supports 4-byte address opcodes.
sfdp-bfp	uint8-array	Contains the 32-bit words in little-endian byte order from the JESD216 Serial Flash Discoverable Parameters Basic Flash Parameters table. This provides flash-specific configuration information in cases were runtime retrieval of SFDP data is not desired.
enter-4byte-addr	int	Enter 4-Byte Addressing value from JESD216 BFP DW16 This property is ignored if the device is configured to use SFDP data from the sfdp-bfp property (CONFIG_SPI_NOR_SFDP_DEVICETREE) or to read SFDP properties at runtime (CONFIG_SPI_NOR_SFDP_RUNTIME). For CONFIG_SPI_NOR_SFDP_MINIMAL this is the 8-bit value from bits 31:24 of DW16 identifying ways a device can be placed into 4-byte addressing mode. If provided as a non-zero value the driver assumes that 4-byte addressing is require to access the full address range, and automatically puts the device into 4-byte address mode when the device is initialized.
page-size	int	Number of bytes in a page from JESD216 BFP DW11 This property is only used in the CONFIG_SPI_NOR_SFDP_MINIMAL configuration. It is ignored if the device is configured to use SFDP data from the sfdp-bfp property (CONFIG_SPI_NOR_SFDP_DEVICETREE) or if the SFDP parameters are read from the device at runtime (CONFIG_SPI_NOR_SFDP_RUNTIME). The default value is 256 bytes if the value is not specified.