st,stm32h7-fmc

Note

An implementation of a driver matching this compatible is available in drivers/memc/memc_stm32.c.

Description

STM32 Flexible Memory Controller (FMC).

The FMC allows to interface with static-memory mapped external devices such as
SRAM, NOR Flash, NAND Flash, SDRAM...

All external memories share the addresses, data and control signals with the
controller. Each external device is accessed by means of a unique chip select.
The FMC performs only one access at a time to an external device.

The flexible memory controller includes three memory controllers:

  - NOR/PSRAM memory controller
  - NAND memory controller (some devices also support PC Card)
  - Synchronous DRAM (SDRAM/Mobile LPSDR SDRAM) controller

Each memory controller is defined below the FMC DeviceTree node and is managed
by a separate Zephyr device. However, because signals are shared the FMC
device handles the signals and the peripheral clocks. FMC can be enabled
in your board DeviceTree file like this:

&fmc {
    status = "okay";
    pinctrl-0 = <&fmc_nbl0_pe0 &fmc_nbl1_pe1 &fmc_nbl2_pi4...>;
};

Properties

Properties not inherited from the base binding file.

Name	Type	Details
`st,mem-swap`	`string`	The FMC bank mapping configuration (BMAP bits of FMC_BCR1). * disable - Default mapping. * sdram-sram - Swap the NOR/PSRAM bank with SDRAM. * sdramb2 - Remaps the SDRAM bank2. If absent, then default mapping (disable) is used (reset state). Default value: `disable` Legal values: `'disable'`, `'sdram-sram'`, `'sdramb2'`
`pinctrl-0`	`phandles`	Pin configuration/s for the first state. Content is specific to the selected pin controller driver implementation. This property is required.
`pinctrl-names`	`string-array`	Names for the provided states. The number of names needs to match the number of states. This property is required.
`pinctrl-1`	`phandles`	Pin configuration/s for the second state. See pinctrl-0.
`pinctrl-2`	`phandles`	Pin configuration/s for the third state. See pinctrl-0.
`pinctrl-3`	`phandles`	Pin configuration/s for the fourth state. See pinctrl-0.
`pinctrl-4`	`phandles`	Pin configuration/s for the fifth state. See pinctrl-0.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “st,stm32h7-fmc” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`clocks`	`phandle-array`	Clock gate information This property is required.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) See Important properties for more information. This property is deprecated.
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`mboxes`	`phandle-array`	mailbox / IPM channels specifiers
`mbox-names`	`string-array`	Provided names of mailbox / IPM channel specifiers
`power-domains`	`phandle-array`	Power domain specifiers
`power-domain-names`	`string-array`	Provided names of power domain specifiers
`#power-domain-cells`	`int`	Number of cells in power-domains property
`zephyr,deferred-init`	`boolean`	Do not initialize device automatically on boot. Device should be manually initialized using device_init().
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.
`zephyr,pm-device-runtime-auto`	`boolean`	Automatically configure the device for runtime power management after the init function runs.
`zephyr,disabling-power-states`	`phandles`	List of power states that will disable this device power.