solomon,ssd1673 (on mipi-dbi bus)

Vendor: Solomon Systech Limited

Description

Solomon Systech SSD1673 250x150 EPD display controller

Properties

Top level properties

These property descriptions apply to “solomon,ssd1673” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

Name

Type

Details

supply-gpios

phandle-array

GPIO specifier that controls power to the device.

This property should be provided when the device has a dedicated
switch that controls power to the device.  The supply state is
entirely the responsibility of the device driver.

Contrast with vin-supply.

vin-supply

phandle

Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.

This property should be provided when device power is supplied
by a shared regulator.  The supply state is dependent on the
request status of all devices fed by the regulator.

Contrast with supply-gpios.  If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.

mipi-max-frequency

int

Maximum clock frequency of device's MIPI interface in Hz

mipi-mode

int

MIPI DBI mode in use. Use the macros, not the actual enum value. Here is
the concordance list (see dt-bindings/mipi_dbi/mipi_dbi.h)
  1     MIPI_DBI_MODE_SPI_3WIRE
  2     MIPI_DBI_MODE_SPI_4WIRE
  3     MIPI_DBI_MODE_6800_BUS_16_BIT
  4     MIPI_DBI_MODE_6800_BUS_9_BIT
  5     MIPI_DBI_MODE_6800_BUS_8_BIT
  6     MIPI_DBI_MODE_8080_BUS_16_BIT
  7     MIPI_DBI_MODE_8080_BUS_9_BIT
  8     MIPI_DBI_MODE_8080_BUS_8_BIT

Legal values: 1, 2, 3, 4, 5, 6, 7, 8

duplex

int

SPI Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Selecting half duplex allows to use SPI MOSI as a bidirectional line,
typically used when only one data line is connected.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
  0    SPI_FULL_DUPLEX
  2048 SPI_HALF_DUPLEX

mipi-cpol

boolean

SPI clock polarity which indicates the clock idle state.
If it is used, the clock idle state is logic high; otherwise, low.

mipi-cpha

boolean

SPI clock phase that indicates on which edge data is sampled.
If it is used, data is sampled on the second edge; otherwise, on the first edge.

mipi-hold-cs

boolean

In some cases, it is necessary for the master to manage SPI chip select
under software control, so that multiple spi transactions can be performed
without releasing it. A typical use case is variable length SPI packets
where the first spi transaction reads the length and the second spi transaction
reads length bytes.

height

int

Height of the panel driven by the controller, with the units in pixels.

This property is required.

width

int

Width of the panel driven by the controller, with the units in pixels.

This property is required.

softstart

uint8-array

Booster soft start values

busy-gpios

phandle-array

BUSY pin.
The BUSY pin of SSD16XX is active high. If connected directly the MCU pin should be configured as active high.

This property is required.

tssv

int

Temperature Sensor Selection Value
Display controller can have integrated temperature sensor or an external temperature sensor is connected to the controller. The value selects which sensor should be used.

rotation

int

Display rotation (CW) in degrees. If not defined, rotation is off by default.

Legal values: 0, 90, 180, 270

Child node properties

Name

Type

Details

lut

uint8-array

LUT associated with this profile.

gdv

uint8-array

Gate driving voltage values

sdv

uint8-array

Source driving voltage values

vcom

int

VCOM voltage

border-waveform

int

Border waveform

dummy-line

int

Dummy line period override.

gate-line-width

int

Gate line width override.