EFR32FG1 2400/868 MHz 13 dBm Dual Band (SLWRB4250B)

Overview

The EFR32FG1 Flex Gecko 2.4 GHz and 868 MHz Radio Board is delivered as part of SLWSTK6061B Proprietary Wireless Starter Kit. It contains a EFR32FG1 Wireless SoC built on an ARM Cortex®-M4F processor with excellent low power capabilities.

The BRD4250B a.k.a. SLWRB4250B radio board plugs into the Wireless Starter Kit Mainboard BRD4001A and is supported as one of Radio Boards.

Hardware

  • EFR32FG1P133F256GM48 Flex Gecko SoC

  • CPU core: ARM Cortex®-M4 with FPU

  • Flash memory: 256 kB

  • RAM: 32 kB

  • Transmit power: up to +13 dBm

  • Operation frequency: 2.4 GHz, 868 MHz

  • 8Mbit SPI NOR Flash

  • Crystals for LFXO (32.768 kHz) and HFXO (38.4 MHz).

For more information about the EFR32FG1 SoC and BRD4250B board, refer to these documents:

Supported Features

The board configuration supports the following hardware features:

Interface

Controller

Driver/Component

MPU

on-chip

memory protection unit

NVIC

on-chip

nested vector interrupt controller

SYSTICK

on-chip

systick

COUNTER

on-chip

rtcc

FLASH

on-chip

flash memory

GPIO

on-chip

gpio

UART

on-chip

serial port-polling; serial port-interrupt

SPI(M)

on-chip

spi port-polling

WATCHDOG

on-chip

watchdog

The default configuration can be found in boards/silabs/radio_boards/slwrb4250b/slwrb4250b_defconfig

Connections and IOs

In the following table, the column Pin contains Pin names. For example, PA2 means Pin number 2 on PORTA, as used in the board’s datasheets and manuals.

Pin

Function

Usage

PF4

GPIO

LED0

PF5

GPIO

LED1

PF6

GPIO

Push Button PB0

PF7

GPIO

Push Button PB1

PA5

GPIO

Board Controller Enable VCOM_ENABLE

PA0

USART0_TX

UART Console VCOM_TX US0_TX #0

PA1

USART0_RX

UART Console VCOM_RX US0_RX #0

PC6

SPI_MOSI

Flash MOSI US1_TX #11

PC7

SPI_MISO

Flash MISO US1_RX #11

PC8

SPI_SCLK

Flash SCLK US1_CLK #11

PA4

SPI_CS

Flash Chip Select (GPIO)

System Clock

The EFR32FG1P SoC is configured to use the 38.4 MHz external oscillator on the board.

Serial Port

The EFR32FG1P SoC has two USARTs and one Low Energy UARTs (LEUART). USART0 is connected to the board controller and is used for the console.

Programming and Debugging

Flashing

Connect the BRD4001A board with a mounted BRD4250B radio module to your host computer using the USB port.

Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b slwrb4250b samples/hello_world
west flash

Open a serial terminal (minicom, putty, etc.) with the following settings:

  • Speed: 115200

  • Data: 8 bits

  • Parity: None

  • Stop bits: 1

Reset the board and you should see the following message in the terminal:

Hello World! slwrb4250b