SAM E70(B) Xplained

Board Overview

SAM E70(B) Xplained

Vendor:

Atmel Corporation

Architecture:

arm

SoC:

same70q21, same70q21b

Overview

The SAM E70 Xplained evaluation kit is a development platform to evaluate the Atmel SAM E70 series microcontrollers. The current version allows to use both IC variations ATSAME70Q21A(B).

Hardware

• ATSAME70Q21A(B) ARM Cortex-M7 Processor

• 12 MHz crystal oscillator

• 32.768 kHz crystal oscillator (not populated)

• AT24MAC402 EEPROM

• IS42S16100E 16 Mb SDRAM

• SD card connector

• Ethernet port

• Micro-AB USB device

• Micro-AB USB debug interface supporting CMSIS-DAP, Virtual COM Port and Data Gateway Interface (DGI)

• JTAG interface connector

• One reset and one user pushbutton

• One green user LED

Supported Features

The sam_e70_xplained board configuration supports the following hardware features:

Interface	Controller	Driver/Component
NVIC	on-chip	nested vector interrupt controller
SYSTICK	on-chip	systick
AFEC	on-chip	adc
CAN FD	on-chip	can
COUNTER	on-chip	counter
ETHERNET	on-chip	ethernet
GPIO	on-chip	gpio
DAC	on-chip	dac
HWINFO	on-chip	Unique device serial number
I2C	on-chip	i2c
I2S	on-chip	i2s
PWM	on-chip	pwm
SPI	on-chip	spi
UART	on-chip	serial port
USART	on-chip	serial port
USB	on-chip	USB device
WATCHDOG	on-chip	watchdog
XDMAC	on-chip	dma

Other hardware features are not currently supported by Zephyr.

The default configuration can be found in the Kconfig boards/atmel/sam/sam_e70_xplained/sam_e70_xplained_same70q21_defconfig.

Connections and IOs

The SAME70-XPLD User Guide has detailed information about board connections.

System Clock

The SAM E70 MCU is configured to use the 12 MHz external oscillator on the board with the on-chip PLL to generate a 300 MHz system clock.

Serial Port

The ATSAME70Q21 MCU has five UARTs and three USARTs. One of the USARTs is configured for the console and is available as a Virtual COM Port via EDBG USB chip.

Programming and Debugging

Flashing the Zephyr project onto SAM E70 MCU requires the OpenOCD tool. Support for Atmel SAM E microcontroller series was added in OpenOCD release 0.10.0, which was added in Zephyr SDK 0.9.2.

By default a factory new SAM E70 chip will boot SAM-BA boot loader located in the ROM, not the flashed image. This is determined by the value of GPNVM1 (General-Purpose NVM bit 1). The flash procedure will ensure that GPNVM1 is set to 1 changing the default behavior to boot from Flash.

If your chip has a security bit GPNVM0 set you will be unable to program flash memory or connect to it via a debug interface. The only way to clear GPNVM0 is to perform a chip erase procedure that will erase all GPNVM bits and the full contents of the SAM E70 flash memory:

• With the board power off, set a jumper on the J200 header.

• Turn the board power on. The jumper can be removed soon after the power is on (flash erasing procedure is started when the erase line is asserted for at least 230ms)

Flashing

1. Run your favorite terminal program to listen for output. Under Linux the terminal should be /dev/ttyACM0. For example:

   $ minicom -D /dev/ttyACM0 -o
   

   The -o option tells minicom not to send the modem initialization string. Connection should be configured as follows:

   • Speed: 115200

   • Data: 8 bits

   • Parity: None

   • Stop bits: 1

2. Connect the SAM E70 Xplained board to your host computer using the USB debug port. Then build and flash the Hello World application.

   # From the root of the zephyr repository
   west build -b sam_e70_xplained/same70q21 samples/hello_world
   west flash
   

   You should see “Hello World! sam_e70_xplained” in your terminal.

3. To use the SoC variation B IC, you need type “sam_e70_xplained/same70q21b”.

   # From the root of the zephyr repository
   west build -b sam_e70_xplained/same70q21b samples/hello_world
   west flash
   

   You should see “Hello World! sam_e70_xplained” in your terminal.

You can flash the image using an external debug adapter such as J-Link or ULINK, connected to the 20-pin JTAG header. Supply the name of the debug adapter (e.g., jlink) via an OPENOCD_INTERFACE environment variable. OpenOCD will look for the appropriate interface configuration in an interface/$(OPENOCD_INTERFACE).cfg file on its internal search path.

Debugging

You can debug an application in the usual way. Here is an example for the Hello World application.

# From the root of the zephyr repository
west build -b sam_e70_xplained/same70q21 samples/hello_world
west debug

References

SAM E70 Product Page:

http://www.atmel.com/products/microcontrollers/arm/sam-e.aspx